Got only 60 seconds?Answer: On the waste side of the cut line, center the saw blade. 4. Firmly grasp the saw and lower the blade into the material to be cut. Continue holding the blade in the down position after the cut is finished, release the on/off switch, wait until the blade stops rotating, and then raise the blade to the up position.
The motorized miter saw blade should be aligned with the cutting line. The blade should be perpendicular to the workpiece, and the teeth should be pointing in the direction of the cut. The blade should be positioned so that the kerf is centered on the cutting line.
1How Can The Saw Operator Prevent The Blade From Binding When Cutting Stock On The Powered Miter Saw
When cutting warped, bowed, or long stock, how can the saw operator keep the blade from binding? the stock to the table with a clamp.
2How Do You Check A Miter Saw Alignment
Place your square on its edge with one edge flat on the table and the other edge rising straight up from the table to check the bevel angle. Slide the square so that its vertical edge is parallel to the blade while lowering the saw (with the blade guard raised).
3How Should Stock Be Held When Operating The Saw
1. Stocks need to be kept. For all crosscuts, keep both feet firmly on the table and up against the fence. 2. Check that the blade height is appropriate and that all clamps are tight before starting the motor.
4Which Of The Following Is The Correct Procedure To Determine If The Blade Is Operating On The Middle Of The Band Saw Wheel
A bandsaw that has been installed correctly will have teeth on its blade that point downward and in the direction of blade travel. 3. Regularly check the blade’s tracking and tension, and adjust as necessary. Disconnect the power and manually turn the wheels. to check that the blade is tracking centrally on the wheel.
5How Must The Saw Blade Be Held After The Cut Is Finished And Before The Blade Stops Rotating Quizlet
After the cut is complete but before the saw blade stops rotating, how should it be held? the stock to the table with a clamp.
6What Type Of Stock Should Never Be Ripped On The Table Saw
Which stock material ought never to be ripped on a table saw? circular stock Which of the following table saw operations needs a push stick to be used? tearing thin materials.
7In Which Direction Should The Teeth Face When Inserting A Blade In This Tool
Which way should the teeth of a hacksaw be facing? The hacksaw blade should be installed with the teeth facing forward. The blade of the saw will cut when it is pushed (the forward stroke) as opposed to when it is pulled (see photo).
8How Far Should Your Fingers Be From The Blade
Keep your fingers away from the saw blade’s edge. Keep your fingers away from the saw blade at all times. You need to position your fingers. when the saw is running, more than two inches from the blade. Put your cylindrical (round) stock in a “V” fixture before cutting it.
9What Should You Do If The Stock Binds Or Pinches The Blade
Never back the stock off the blade; otherwise, kickback will happen. Turn off the saw and wait until it comes to a complete stop before making an attempt to remove the blade from the stock if the saw blade becomes stuck on a piece of stock.
10How Do You Lock The Blade On A Dewalt Miter Saw
Press the handle down until the blade is as low as it will go to lock the saw. After that, to secure the blade in place, push the lock pin back into the rail. Pulling up on the handle while the pin is pushed in will reveal whether the saw is locked. The saw is locked if the handle stays still.
11How Far Above Your Wood Should The Blade Guard Be On The Band Saw
Check the blade’s tightness. Set the guard at about 14″ above the work piece. Turn on dust collection and open the blast gate. Start the saw.
12What Should You Do To Ensure Your Safety Before Crosscutting With A Radial Arm Saw
What safety precautions ought to be taken when employing a radial arm saw? Put on safety goggles, safety glasses with side shields, or a face shield (with safety glasses or goggles).. Put on hearing protection that is appropriate for the volume and frequency of noise to which you are exposed in the workshop.
Related Articles: